search

AMT Datasouth Fastmark M4 Series Podręcznik Użytkownika Strona 55

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
Przeglądanie stron 54
~ 55 ~
Troubleshooting
The following guide lists the most common problems that may be encountered when
operating this bar code printer. If the printer still does not function after all suggested
solutions have been invoked, please contact the Customer Service Department of your
purchased reseller or distributor for assistance.
Problem
Possible Cause
Recovery Procedure
Power indicator does not
illuminate
*
The battery is not
properly
installed.
*
Battery out of power.
*
The battery is dead.
*
Reinstall the battery.
*
Switch the printer on.
*
Charge the battery.
*
Replace a new battery.
Not Printing
*
Check if interface cable is well
connected to the interface
connector.
*
Check if wireless or Bluetooth
device is well connected
to
h
ost and printer.
*
The port specified in the
Windows driver is not correct.
*
Re-connect cable to interface.
*
Please reset the wireless device
setting.
*
Select the correct printer port in the
driver.
No print on the label
*
Label loaded not correctly.
*
Use wrong type paper
*
Follow the instructions in loading the
media.
*
Use thermal type paper.
The printer status from
DiagTool or LCD shows
“Head
Open”.
* The printer carriage is open.
* Please close the print carriage.
The printer status from
DiagTool or LCD shows
“Out
of Paper”.
*
Running out of media roll.
*
The media is
installed
incorrectly.
*
Media sensor is not calibrated.
*
Supply a new media roll.
*
Follow the instructions in loading the
media to reinstall the media roll.
*
Calibrate the media sensor.
The printer status from
DiagTool or LCD shows
“Paper
Jam”.
*
Media sensor is not set properly.
*
Make sure media size is
set
properly.
*
Label may be stuck inside the
printer mechanism.
*
Calibrate the media sensor.
*
Set media size correctly.
*
Remove the stuck label inside the
printer mechanism.
The printer status from
LCD
shows "Strong
light. Press
FEED to
print."
* Peel-off sensor can’t work in
strong light place.
* Remove the printer to proper place
to
print for peer-off mode.
Can’t downloading the file
to
memory (FLASH /
DRAM/CARD)
* The space of memory is full.
*
Delete unused files in the memory.
*
256 is the maximum number of
allowable DRAM files.
*
The maximum user addressable
memory
space of DRAM is
2048KB.
*
256 is the maximum number of
allowable FLASH files.
*
The max. user addressable memory
space of FLASH is14336KB.
Przeglądanie stron 54
1 2 ... 50 51 52 53 54 55 56 57 58 59 60 61 62

Komentarze do niniejszej Instrukcji

Brak uwag
Powiązane produkty i podręczniki dla Czytniki kodów kreskowych AMT Datasouth Fastmark M4 Series
Czytniki kodów kreskowych AMT Datasouth Fastmark M6 PLUS Series Podręcznik Użytkownika   (83 strony)
Czytniki kodów kreskowych AMT Datasouth Fastmark M4 Series Instrukcja Obsługi   (19 strony)
Czytniki kodów kreskowych AMT Datasouth Fastmark M6 PLUS Series Podręcznik Użytkownika   (32 strony)
Czytniki kodów kreskowych AMT Datasouth Fastmark M1 Podręcznik Użytkownika   (532 strony)
  • Nor-cal BananaGold Delt Breville Monitor
  • Niles Audio Klawiatury numeryczne ActionTec Karty sieciowe CNET Networking Solio Nie Actron Skrzynie na sprzęt
  • Humanscale T7 Acer S1200 Broan RML3342S Lr-baggs Duet II Commax CDV-43Q
  • Panasonic ES762 Instrukcja Użytkownika Hamilton Beach 40514 Instrukcja Obsługi AMX NXC-ME260-64 Instrukcja Użytkownika Vivitar VIVICAM 5028 Instrukcja Użytkownika Bernina Artista 200 Instrukcja Użytkownika